Windows 2000 Server
You have just configured two Windows NT Servers, Monitor 1 and Monitor 2 with no other software installed. You have an application server that needs to be monitored for performance to figure out what it's problem is, or to get some kind of baseline. You install Network Monitor on Monitor 2. What would you do to monitor Application server?

Configure Monitor 2 and Application server as monitoring partners (or something) to monitor the performance
Install Network Monitor on Monitor 1
Install Network Monitor on Application Server
Configure the network monitor ECP port something for TCP
Configure the network monitor EDP port something for UDP

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
The network uses TCP/IP as the only network protocol. You configure the remote access server on the network. Some users report that when they connect to the server they receive the following message |" IPX SPX compatible computer deported error 733" The EPP control network protocol for the network is not available. If the users allow the connection to continue they are able to connect to the services that use TCP/IP. You want to prevent this message from being displayed. What should you do?

Configure a client computer to use only TCP/IP for the connections to the remote access server
Configure the remote access server to allow IPX based remote access demand dial connections
None of above
Configure the client computer to use a defined IPX network address for the connection to the remote access servers
Configure the remote access server to disable multi-link connection

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of a Windows 2000 Server computer that has FIVE hard disks. Four 100 GB hard disks on the server are configured as a single stripe volume. You want to reconfigure the fourth disk so that the volume is fault tolerant and has as much space possible available for storing data. You want to use only existing hardware. What should you do?

None of above
Backup the data on the stripe volume and delete the stripe
Convert the disk to dynamic disk shut doWn and restart the server
Backup the data on the stripe volume and delete the stripe volume. Create a raidS volume on the four disks, restore the data to the new raid5 volume
Backup the data on the stripe volume and delete the stripe volume. Create a mirror volume, shut down and restart the server. Restore the data to new mirror volumes

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of a Windows 2000 domain that has three domain controllers. Each day, you use Windows Backup to perform full backups of each domain controller. You run a script to make changes to account information in Active Directory. As a result of errors in the script, the incorrect user accounts are modified. Active Directory replication then replicates the changes to the other two domain controllers. You want to revert Active Directory to the version that was backed up the previous day. What should you do?

On a single domain controller, use Windows Backup to restore the System State data. Shut down and restart the computer
Shut down, and restart a single domain controller by using the Recovery Console. Use Windows Backup to restore the System State data. Exit the Recovery Console. Restart the computer
None of above
Shut down and restart each domain controller by using the Recovery Console. Use Windows Backup to restore the Sysvol folder. Exit the Recovery Console. Restart the computer
Shut down and restart a single domain controller in directory services restore mode. Use Windows Backup to restore the System State data. Run the Ntdsutil utility. Restart the computer

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your Windows 2000 Server computer contains a stripe set with parity on a four-disk array. You convert the stripe set with parity to a dynamic RAID-5 volume. Six months later, users report that disk access on the server is slower than it had been on the previous day, You use Disk Management and discover that the status of the third disk in the array is Missing. You want to recover the failed RAID-5 volume. What should you do first?

Ensure that the third disk is attached to the server and has power. Use Disk Management to repair the volume
Ensure that the third disk is attached to the server and has power. Use Disk Management to reactivate the disk
Install a new disk and create a single extended partition on the new disk. Restart the computer and allow Windows 2000 to automatically repair the volume on the extended partition
Replace the third disk and restart the server. Use disk Management to repair the volume
None of above

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your company's network includes Windows 3.1 client computers, Windows 95 client computers, and Windows 2000 Professional client computers. The company's manufacturing facilities run 24 hours per day. The company has developed its own 32-bit application that collects information from the manufacturing process so that workers on one shift can find out that was manufactured during the previous shift. The company wants to make the application available on all of the client computers by using Terminal Service on a Windows 2000 Server computer. This server will not run as a domain controller. You install Terminal Services. The information technology (IT) department needs to be able to remote control users' sessions to support and troubleshoot the application. What should you do to enable the IT department to control users' sessions?

None of above
Configure the Terminal server to run in Remote Administration mode
Grant the IT department Full Control permission to the Remote Desktop Protocol (RDP) on the Terminal server
Add the members of the IT department to the Power Users group on the Terminal server
Use third-party software to enable remote control of users' sessions

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server