Windows 2000 Server
You have configured a Group Policy Object (GPO) for the marketing oranization unit (OU) to prevent users from accessing My Network Places and from running System in Control Panel. You want the Managers Domain Local Group to be able to access My Network Places, but you still want to prevent them from running System in Control Panel. What should you do?

None of above
Create a second GPO in the OU. Add the Managers group to the access control list. Allow the managers group to apply the Group Policy. Deny the Authenticated Users group permission to read and apply th
Create a second GPO in the OU. Add the Managers group to the access control list. Allow the managers group to apply the Group Policy. Disable the Authenticated Users group permission to read and apply
Add the Managers group to the access control list of the GPO. Disable the permission of the managers group to read and apply the Group Policy
Add the Managers group to the access control list of the GPO. Deny the permission of the managers group to read and apply the Group Policy

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You install the Routing and Remote Access service on a Windows 2000 Server computer in your network. Your network is not directly connected to the Internet and uses the private IP address range 192.168.0.0. When you use Routing and Remote Access to dial in to the server, your computer connects successfully, but you are unable to access any resources. When you try to piiig servers by using their IP addresses, you receive the following message: "Request timed out." When you run the ipconfig command, it shows that your dial-up connection has been given the IP address 169.254.75.182. What should you do to resolve the problem?

Configure the remote access server to act as a DHCP Relay Agent
Configure the remote access server with the address of a DHCP server
Authorize the remote access server to receive multiple addresses from a DHCP server
None of above
Ensure that the remote access server is able to connect to a DHCP server that has a scope for its subnet

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You have just configured two Windows NT Servers, Monitor 1 and Monitor 2 with no other software installed. You have an application server that needs to be monitored for performance to figure out what it's problem is, or to get some kind of baseline. You install Network Monitor on Monitor 2. What would you do to monitor Application server?

Configure the network monitor EDP port something for UDP
Install Network Monitor on Monitor 1
Configure Monitor 2 and Application server as monitoring partners (or something) to monitor the performance
Install Network Monitor on Application Server
Configure the network monitor ECP port something for TCP

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your network is configured as shown in the exhibit. "Engineering! and Salesl have DHCP installed up them." All the servers are Windows 2000 Server computers that use TCP/IP as the only network protocol. The sales department uses one subnet and has servers named Salesl and Sales2. The engineering department uses another subnet and has servers named Engineeringl and Engineering2. Salesl and Engineeringl are configured to act as DHCP servers. The router that joins the two subnets is not RFC 1542 compliant and does not support DHCP/BOOTP relay. You want to allow Salesl and Engineeringl to support client computers on each other's subnets. What should you do?

On Engineering2 and Sales2, install and configure the DHCP Relay Agent service
None of above
Set the router option in the DHCP Scopes to 192.168.2.1 for Engineeringl and 192.168.1.1 for Salesl
On Engineering2 and Sales2, install Routing and Remote Access, and configure RIP as a routing protocol
Configure Engineering2 and Sales2 as DHCP servers without any scopes

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You want to provide complete redundancy for all data stored on your hardware RAID 5 array. You install second h/w Raid 5. You want to create a mirror set of the original array. However when you right click the free space on new array you see no option to create a new volume or mirrrored volume. What should you do?

Create a single unformatted primary partition on new array
Format the new disk array as a single NTFS logical drive in an extended partition.
Convert both to dynamic disks
Format new disk array as a single NTFS primary partition
Create an empty extended partition on new disk

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of contoso.local domain. You organize the domain into organizational units as shown in the EXHIBIT. You configure the local security options and other settings for the default domain policy object You delegate administration of Michigan and Florida OU. You want to prevent those administrators from creating any other group policy objects with settings that conflict with those you configured.What should you do?

Block the group policy inheritance for Michigan and Florida OU
Block the group policy inheritance for the contoso.local domain
From the group policy options from the Michigan and Florida OU, set the option not override
None of above
From the group policy options from the contoso.local domains set the option not override

ANSWER DOWNLOAD EXAMIANS APP