Windows 2000 Server
You are the administrator of a Windows 2000 Server network that runs in mixed mode. You install a new Windows 2000 Server computer. You create and share a new HP LaserJet 4L printer. Your Windows 2000 Professional client computers can print to the new printer successfully. However, when users try to connect to the printer from Windows NT Workstation 4.0 client computers, they receive the dialog box shown in the exhibit. "The server on which the printer resides does not have a suitable HP LaserJet printer driver installed". You want the printer driver to be installed automatically on the Windows NT Workstation computers. What should you do?

Change the sharing options on the printer to install additional drivers for Windows NT 4.0 or Windows 2000
Copy the Windows NT 4.0 printer drivers to the WinntSystem32 pri liter sdri vers folder on the Windows 2000 print server
None of above
Copy the Windows NT 4.0 Printer Drivers to the Net logon shared folders on all Windows NT Server 4.0 computers still configured as BDCs
Copy the Windows NT 4.0 printer drivers to the Net logon shared folder on the PDC emulator

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You want to improve the TCP transmission speed of a Windows 2000 Server computer. You also want to remove an unused registry key. You use Regedit32 to edit the registry of the Windows 2000 Server. You insert a value in the registry named TCPWindowSize, and you remove the unused key. You restart the computer, but the computer stops responding before the logon screen appears. You want to return the computer to its previous configuration. What should you do?

Restart the computer by using the Recovery Console. Run the enable winlogon service_auto_start command, and then run the Exit command
Restart the computer by using the Recovery Console. Run the Fixboot c: command, and then run the Exit command
Restart the computer by using the last known good configuration
None of above
Restart the computer in safe mode. Then restart the computer again

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
The network uses TCP/IP as the only network protocol. You configure the remote access server on the network. Some users report that when they connect to the server they receive the following message |" IPX SPX compatible computer deported error 733" The EPP control network protocol for the network is not available. If the users allow the connection to continue they are able to connect to the services that use TCP/IP. You want to prevent this message from being displayed. What should you do?

None of above
Configure the client computer to use a defined IPX network address for the connection to the remote access servers
Configure the remote access server to disable multi-link connection
Configure the remote access server to allow IPX based remote access demand dial connections
Configure a client computer to use only TCP/IP for the connections to the remote access server

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your network is configured as shown in the exhibit. "Engineering! and Salesl have DHCP installed up them." All the servers are Windows 2000 Server computers that use TCP/IP as the only network protocol. The sales department uses one subnet and has servers named Salesl and Sales2. The engineering department uses another subnet and has servers named Engineeringl and Engineering2. Salesl and Engineeringl are configured to act as DHCP servers. The router that joins the two subnets is not RFC 1542 compliant and does not support DHCP/BOOTP relay. You want to allow Salesl and Engineeringl to support client computers on each other's subnets. What should you do?

On Engineering2 and Sales2, install and configure the DHCP Relay Agent service
Set the router option in the DHCP Scopes to 192.168.2.1 for Engineeringl and 192.168.1.1 for Salesl
On Engineering2 and Sales2, install Routing and Remote Access, and configure RIP as a routing protocol
None of above
Configure Engineering2 and Sales2 as DHCP servers without any scopes

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of Windows 2000 domain and TWO Windows NT domains. The Windows 2000 domains trust each of the Windows NT domains. Each of Windows NT domains trust the Windows 2000 domain. A Windows 2000 domain controller named DC1 is configured to use a highly secure domain controller template. Users in the Windows NT domain report that they cannot access DC1. You need to allow the users of computers in the Windows NT domain to access resources on DC1. What should you do?

None of above
Apply a less restrictive custom security template to DC1
Apply a less restrictive custom policy to Windows NT domain controller
Ensure the Windows 2000 domain is configured in the mixed mode
Ensure the Windows 2000 domain is configured to run in the native mode

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Some applications on your company network use defined domain user accounts as their service accounts. Each computer that runs one of these applications should have the respective service account in the Local Administrators Group. Currently, you individually place these service accounts in the Local Administrators Group on the appropriate Windows 2000 Professional computers. You need to centralize this process. What should you do?

Add the applications service accounts to the Domain Administrator Group
Add the applications service accounts to the Local Administrator Group. Use the Restricted Groups option in each computer's local group policy
Add the applications service accounts to the Local Administrator Group. Use the Restricted Groups option in an OU Group Policy
Add the applications service accounts to the Local Administrator Group. Use the Restricted Groups option in a Domain Group Policy
None of above

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server